2000M Long Range 1 CH 30A DC Power Output RF Wireless Remote Control Kit

Description

0020527
2000M  Long Range 1 CH 30A DC Power Output RF Wireless  Remote Control Kit
With Waterproof and External Telescopic Antenna
Model: 0020058
Package  Include:
1 x Receiver: S1PX-DC06-ANT3 / S1PX-DC09-ANT3  / S1PX-DC12-ANT3 / S1PX-DC24-ANT3
1 x Transmitter: CB-1
1 x User manual
Feature:
Application: It can be used in industry  automation, agriculture automation and home automation, such as factory, house,  farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call,  etc. It can remote control equipments on land, water and air, such as remote  control lights, sirens, locks, motors, fans, winches, blinds, linear actuators,  doors, windows, electric solenoid valves, security alarm, business signs and  various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case  and waterproof connector, it can be installed outdoors.
DC Power  Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.
High Power:  Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V,  270W/9V, 720W/24V.
With wired control terminals: You can connect  sensors, limit switches, manual switches or external devices to control the  receiver.
With the external antenna, it can have a  further working range.
Design with low-power and high-speed CMOS  technology.
You can turn on/ off the receiver with  transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls,  floors, doors or windows.
With reverse power protection and over current  protection.
Reliable control: The receiver only works with  the transmitter which use same code.
One/several transmitters can control  one/several receivers simultaneously.
You can use two or more units in the same  place.
Receiver:
Model No.: S1PX-DC06-ANT3 / S1PX-DC09-ANT3 / S1PX-DC12-ANT3 /  S1PX-DC24-ANT3
Power Supply (Operating Voltage): DC6V (S1PX-DC06-ANT3), DC9V±1V  (S1PX-DC09-ANT3), DC12V±1V (S1PX-DC12-ANT3), DC24V±2V (S1PX-DC24-ANT3)
Output: DC6V (S1PX-DC06-ANT3), DC9V (S1PX-DC09-ANT3), DC12V  (S1PX-DC12-ANT3), DC24V (S1PX-DC24-ANT3)
Working Frequency: 315MHz / 433MHz
Channel: 1CH
Control Modes: Toggle, Momentary, Latched
Static Current: ≤6mA
Maximum Working Current: 30A / each channel
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Work with Fixed code transmitters or Learning code transmitters.
Transmitter:
Model No.: 0021023 (CB-1)
Channel/Button: 1
Button Symbol: no symbol
Operating Voltage: 9V (1  x 6F22 -9V battery, can be used for 12 months)
Operating Current: 30mA
Operating Frequency:  315Mhz / 433Mhz
Encoding Chip: PT2262 / PT2264 / SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance:  1000m / 3000ft (theoretically)
The distance of 1000m is a theoretical data, it shall be operated  in an open ground, no barriers, no any interference. But in the practice, it  will be hindered by trees, walls or other constructions, and will be exposed to  some interference by other signals. Therefore, the actual distance may or may  not reach 1000m.
If you stretches the telescopic antenna, it can have a further  working range, which is twice as much as it used to be.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 135mm x 42mm x 25mm
Weight: 95g
Uses: garage doors, motorcycles, car alarm products, home  security products, wireless remote control products, industrial control  products.
Matching Transmitters:
The receiver can work with different transmitters, such as model  C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2/CV-2 (500M), or  CB-1 / CB-2 (1000M), CBW-1/CBW-2 (1000M, waterproof) etc.
When you set the receiver in toggle or momentary mode, it should  work with single button transmitter, such as model C-1 (100M), CWB-1 (50M,  waterproof), CP-1 (500M), or CB-1 (1000M), CBW-1 (1000M, waterproof) etc. When  you set the receiver in latched mode, it should work with two buttons  transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M),  CV-2 (500M), CB-2 (1000M), or CBW-2 (1000M, waterproof) etc.
Working Range:
Super long range, with a transmitter (such as  CB-2) to form a complete set, the maximum working distance can reach 2000M in an  open ground.
The maximum working distance is a theoretical  data, it shall be operated in an open ground, no barriers, no any interference.  But in the practice, it will be hindered by trees, walls or other constructions,  and will be interfered by other wireless signals. Therefore, the actual distance  may not reach this maximum working distance.
External Telescopic Antenna:
Length of external telescopic antenna: 108mm /  445mm (stretch)
With SMA connector.
If you stretches the external telescopic  antenna, it can have a further working range.
Usage:
The receiver can be used to control DC 6V / 9V  / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you  should choose the receiver with same DC 12V version; and if the power supply of  those equipments is DC 24V, you should choose the receiver with same DC 24V  version.
Wiring:
If you want to control a DC 12V lamp, do as  following:
1) Connect the positive pole of DC power supply to terminal “L / +” of INPUT,  and connect the negative pole of DC power supply to terminal “N / -” of INPUT.
2) Connect the positive pole of lamp to terminal "L / +" of OUTPUT, and connect  the negative pole of lamp to terminal "N / -" of OUTPUT.
Setting different control modes:
Setting different  control modes (We have set the receiver as Toggle control mode before delivery.  If you want to use other control modes, do as following operation):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (with transmitter CB-1): Press -> On; Press again -> Off.
Press button of the transmitter: Output terminal outputs DC power, the lamp is  on.
Press button again: Output terminal stops outputting, the lamp is off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with transmitter CB-1): Press and hold -> On; Release ->  Off.
Press and hold button of the transmitter: Output terminal outputs DC power, the  lamp is on.
Release button of the transmitter: Output terminal stops outputting, the lamp is  off.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched (with transmitter CB-2): Press -> On, Press another button  -> Off.
Press button A of the transmitter: Output terminal outputs DC power, the lamp is  on.
Press button B of the transmitter: Output terminal stops outputting, the lamp is  off.
Wired control terminals:
The receiver has  manual control terminals, you can connect external devices, sensors, or manual  switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual  terminals 1 (Signal -) and terminal 2 (Signal +), then the external device’s  output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and  terminal 2, turn on the relay. Output terminal outputs DC power, the lamp is on.
When the external device stops to output signal, turn off the relay. Output  terminal stops outputting, the lamp is off.
2) The manual switches:
You can connect manual switch to terminals 1 and 2, and then you can use this  manual switch to control the receiver.
When connect terminals 1 and 2, turn on the relay. Output terminal outputs DC  power, the lamp is on.
And when disconnect terminals 1 and 2, turn off the relay. Output terminal stops  outputting, the lamp is off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for  1- 2 seconds; signal LED on the receiver is on. The receiver enters into status  of LEARNING.
2) Press any one button on transmitter. If  signal LED flashes quickly 15 times and turns off, it means learning is  successful.
3) When receiver is in the status of LEARNING,  press again the button of receiver, signal LED turns off, learning process will  be discontinued.
4) The receiver can learn several remote  controls with different codes.
Delete all transmitters:
We have learned remote control to the  receiver. If you don’t want the receiver to work with the remote control, you  can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the button of  receiver until signal LED flashes slowly; release the button, LED keeps slow  flash. That means all stored codes have been deleted successfully.
Shipping:
Shipping methods: Ship to Worldwide by Airmail.
Delivery time: 10~25 working days (not including week-end and holiday).
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
We will inform you via Email when shipping your items.
FAQs:
Please click  this link to  view
Frequently  Asked  Questions
.
Guarantee:
Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.