2000M Distance 4 Relays DC 9V 12V 24V 5A Wireless Remote Transmitter & Receiver

Description

0020527
2000M  Distance 4 Relays DC 9V 12V 24V 5A Wireless Remote  Transmitter & Receiver
Model: 0020510
Package  Include:
1 x Receiver: S4C-DC09-ANT2 / S4C-DC12-ANT2 /  S4C-DC24-ANT2 (4 Channel / Four Control Modes)
1 x Transmitter: CB-4L
1 x User manual
Feature:
Application: It can be used in industry  automation, agriculture automation and home automation, such as factory, house,  farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call,  etc. It can remote control equipments on land, water and air, such as remote  control lights, sirens, locks, motors, fans, winches, blinds, linear actuators,  doors, windows, electric solenoid valves, security alarm, business signs and  various devices.
Wireless control, easy to install.
Relay Output: This receiver is relay output,  it can be used to operate both DC and AC equipments. The terminals are NO / NC  (normally open / normally closed), which serves as a switch. That means you  should also connect a separate power supply to equipments.
You can turn on/ off the receiver with  transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls,  floors, doors or windows.
With reverse power protection and over current  protection.
Reliable control: The receiver only works with  the transmitter which use same code.
One/several transmitters can control  one/several receivers simultaneously.
You can use two or more units in the same  place.
Receiver:
Model No.: S4C-DC06-ANT2 / S4C-DC09-ANT2 / S4C-DC12-ANT2 /  S4C-DC24-ANT2
Power Supply (Operating  Voltage): DC6V (S4C-DC06-ANT2), DC9V±1V (S4C-DC09-ANT2), DC12V±1V  (S4C-DC12-ANT2), DC24V±2V (S4C-DC24-ANT2)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of  Relay: AC110~240V or DC0~28V
Working Frequency: 315MHz  / 433MHz
Channel: 4 CH
Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
Static Current: ≤6mA
Maximum Working Current:  5A / each channel
PCB size: 68mm x 48mm x 20mm
Case size: 75mm x 55mm x 30mm
Work with Fixed code transmitters or Learning code transmitters.
Transmitter:
Model No.: 0021119 (CB-4L)
Channel/Button: 4
Button Symbol: A, B, C, D
Operating Voltage: 9V (1  x 6F22 -9V battery, can be used for 12 months)
Operating Current: 20mA
Operating Frequency:  315Mhz / 433Mhz
Encoding Chip: EV1527
Encoding Type: Learning code (up to 1 million codes, reducing  code collision and unauthorized code scanning possibilities.)
Transmitting Distance:  1000m / 3000ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 135mm x 42mm x 25mm
Weight: 95g
Magnetic Sucker Antenna:
Frequency Range: 300~450MHz
Impedance: 50Ω
Antenna Length: 15cm
Cable Length:1.5m, we also can offer longer cable, such as  5meters, 10meters, 30meters.
Anti-interference, waterproof, shielded wire set inside.
Magnetic stand design for easy to install.
Matching Transmitters:
The receiver can work with different  transmitters, such as model CWB-4(50M, waterproof), C-4/C-4L (100M), CP-4/CP-4L  (500M), CB-4/CB-4L (1000M), or CBW-4(1000M, waterproof) etc.
Working Range:
Super long range, with a transmitter (such as  CB-4) to form a complete set, the maximum working distance can reach 2000M in an  open ground.
The maximum working distance is a theoretical  data, it shall be operated in an open ground, no barriers, no any interference.  But in the practice, it will be hindered by trees, walls or other constructions,  and will be interfered by other wireless signals. Therefore, the actual distance  may not reach this maximum working distance.
Usage:
The receiver can be used to control both DC  0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not  DC/AC power output. Initial state of relay output terminals: Terminals B and C  are Normally Open; Terminals A and B are Normally Closed.
Wiring:
If you want to control a DC 12V lamp, do as  following:
1) Connect the positive pole of DC power supply to terminal “+” of INPUT, and  connect the negative pole of DC power supply to terminal “-” of INPUT.
2) Connect terminal C to the positive pole of DC power supply, connect terminal  B to the positive pole of DC lamp, and connect the negative pole of DC lamp to  the negative pole of DC power supply.
If you want to control an AC 220V lamp, do  as following:
1) Connect the positive pole of DC power supply to terminal “+” of INPUT, and  connect the negative pole of DC power supply to terminal “-” of INPUT.
2) Connect terminal C to the live wire of AC power supply, connect terminal B to  one side of AC lamp, and connect another side of AC lamp to the neutral wire of  AC power supply.
Setting different control modes:
Setting different  control modes: (We have set the receiver in toggle mode before delivery, if you  want to use other modes, do as following operation.)
Setting control mode Toggle (with the transmitter CB-4): Only connect Jumper-2.
Control mode Toggle (Channel 1~4): Press -> On; Press again -> Off.
Press button A: Turn on relay 1 (connect B and C, disconnect A and B), the lamp  1 is on.
Press button A again: Turn off relay 1 (disconnect B and C, connect A and B),  the lamp 1 is off.
……
Press button D: Turn on relay 4 (connect B and C, disconnect A and B), the lamp  4 is on.
Press button D again: Turn off relay 4 (disconnect B and C, connect A and B),  the lamp 4 is off.
Setting control mode Momentary (with the transmitter CB-4): Only connect  Jumper-1.
Control mode Momentary (Channel 1~4): Press and hold -> On; Release -> Off.
Press and hold button A: Turn on relay 1 (connect B and C, disconnect A and B),  the lamp 1 is on.
Release button A: Turn off relay 1 (disconnect B and C, connect A and B), the  lamp 1 is off.
……
Press and hold button D: Turn on relay 4 (connect B and C, disconnect A and B),  the lamp 4 is on.
Release button D: Turn off relay 4 (disconnect B and C, connect A and B), the  lamp 4 is off.
Setting control mode Latched (with the transmitter CB-4): Disconnect Jumper-1  and Jumper-2.
Control mode Latched (Channel 1~4): Press -> On, other relays Off; Press other  button -> Off.
Press button A: Turn on relay 1 (connect B and C, disconnect A and B), the lamp  1 is on.
Turn off other relays (disconnect B and C, connect A and B), other lamps are  off.
Press button D: Turn on relay 4 (connect B and C, disconnect A and B), the lamp  4 is on.
Turn off other relays (disconnect B and C, connect A and B), other lamps are  off.
Setting control mode Momentary + Toggle (with the transmitter CB-4): Connect  Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1, 2): Press and hold -> On; Release -> Off.
Press and hold button A: Turn on relay 1 (connect B and C, disconnect A and B),  the lamp 1 is on.
Release button A: Turn off relay 1 (disconnect B and C, connect A and B), the  lamp 1 is off.
Press and hold button B: Turn on relay 2 (connect B and C, disconnect A and B),  the lamp 2 is on.
Release button B: Turn off relay 2 (disconnect B and C, connect A and B), the  lamp 2 is off.
Control mode Toggle (Channel 3, 4): Press -> On; Press again -> Off.
Press button C: Turn on relay 3 (connect B and C, disconnect A and B), the lamp  3 is on.
Press button C again: Turn off relay 3 (disconnect B and C, connect A and B),  the lamp 3 is off.
Press button D: Turn on relay 4 (connect B and C, disconnect A and B), the lamp  4 is on.
Press button D again: Turn off relay 4 (disconnect B and C, connect A and B),  the lamp 4 is off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for  1- 2 seconds; signal LED on the receiver is on. The receiver enters into status  of LEARNING.
2) Press any one button on transmitter. If  signal LED flashes quickly 15 times and turns off, it means learning is  successful.
3) When receiver is in the status of LEARNING,  press again the learning button, signal LED turns off, learning process will be  discontinued.
4) The receiver can learn several remote  controls with different codes.
Delete all transmitters:
We have learned remote control to the  receiver. If you don’t want the receiver to work with the remote control, you  can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the learning button  of receiver until signal LED flashes slowly; release the button, LED keeps slow  flash. That means all stored codes have been deleted successfully.
Shipping:
Shipping methods: Ship to Worldwide by Airmail.
Delivery time: 10~25 working days (not including week-end and holiday).
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
We will inform you via Email when shipping your items.
Guarantee:
Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.